User Manual of Postal scales Manual number: ITKU-20-02-01-12-A MANUFACTURER OF ELECTRONIC WEIGHING INSTRUMENTS RADWAG
5. UNPACKING AND ASSEMBLY 5.1. Scales of WPT/P 2 series Unpack and put the scale on a flat even stable surface far away from sources of heat and t
5.2. Scales of WPT/P 60 series Unpack and put the scale on a flat even stable surface far away from sources of heat and then: A. Remove transport
• The surplus cable wind and place inside the pillar as show below: Put the indicator with the hendler on the pillar and tighten up the
• Then you will see zero indication and pictograms: - zero indication - stable result kg - weight unit • If the indication is not zero pre
9. INSCRIPTIONS ON THE DISPLAY No Text string Description 1. FIL Filter level 2. bAud Transmission baud rate 3. Auto Autozero correction 4.
10.2. Browsing user menu Use scale’s keys to move inside the menu. 10.2.1. Keypad + Entering main menu + Inscribing tare value Increasing a
11. WEIGHING Put a load you want to weigh on the weighing pan. When the pictogram appears it means that the result is stable and ready to read. In
11.1. Tarring In order to determine the net mass put the packaging on the pan. After stabilising press - (Net pictogram will be displayed in the l
• Using and set the tare value, • Press , • Program returns to weighings mode. The inscribed tare value can be seen on the display with „–” sig
11.5. Selection of basic weight unit This function is used to set weight unit the scale will start with. Procedure: • Enter the submenu <P
- 2 - JANUARY 2012
• After you select the unit press , the scale returns to: • Return to weighing according to chapter - 10.2.2. Notice: After turning on the sca
Options: A. When [kg] is a basic unit, users can select following units: [kg, lb, N], [lb] is not accessible for verified scales. B. When [g] is
Notice: Filtering level influences the time of stabilization. The higher the filtering level is the longer stabilization time is needed. Return to w
12.3. Autozero function The autozero function has been implemented in order to assure precise indications. This function controls and corrects „0” i
12.4. Tare function This parameters enables users to configure a tare function. Procedure: • Enter the submenu <P1.rEAd> and then: tArA
13. RS 232 PARAMETERS External devices connected to RS 232C have to be supplied from the same mains and common electric shock protection. It preven
13.2. Minimal mass threshold This function is necessary while working with automatic tare. Automatic tarring will not be applied until the indicatio
14.1. Backlight function Program recognises the way the scale is supplied (mains, battery) and automatically selects the way of operating on the ba
14.1.2. Backlight for supplying from batteries The user can change the intensity of backlight from 0% to 100%. The lower the intensity is the longe
bEEP no - switched off bEEP YES - switched on Return to weighing: See 10.2.2. 14.3. Automatic switch-off This function is essential to
- 3 - TABLE OF CONTENTS 1. INTENDED USE ...
Procedure: • Enter the submenu <P5.othr> and then: Returnto weighing: See 10.2.2. 14.4. Battery voltage level check While supplying fr
Procedure: After displaying the level of batteries (in per cents) the program returns to weighing. 14.4.2. Battery discharge pictogram The sym
• Message „nImh” appears on the display, • In case of damaging accumulators or lack of it the pictogram blinks quickly (period about 0.5 sec). No
They need formatting after first powering up. It is crucial for batteries lifetime to undertake this process. Formatting consist in charging and tot
• Following inscriptions will appear • A new start mass is adjusted during this period of time. After that a mass of calibration weight is show
• Return to weighing performing the procedure of saving parameters. Caution: If the calibration process (span adjustment) lasts longer than 15 th
• The process of start mass adjustment can be terminated by pressing , which is signalled on the display: • Return to weighing performing the
Cable diagrams: Cable drawing scale - printer (Kafka) 17. COOPERATION WITH COMPUTER Sending weighing results to the computer can be done: - m
- 38 - 18. COMMUNICATION PROTOCOL 18.1. General information A. A character protocol scale-terminal has been designed for communication between RAD
- 39 - 18.3. Respond message format After sending a request message you can receive: XX_A CR LF command accepted and in progress XX_D CR LF comma
- 4 - 15. USER CALIBRATION ... 33 15.1. Calibrati
- 40 - T_A CR LF T_D CR LF - command accepted and in progress - command completed T_A CR LF T_v CR LF - command accepted and in progress - command
- 41 - Frame format: 1 2-3 4 5 6 7-15 16 17 18 19 20 21 S space stability space sign mass space unit CR LF Example: S CR LF – computer command
- 42 - SU_A CR LF SU_E CR LF - command accepted and in progress - timeout while waiting for stable results SU_I CR LF - command comprehended but can
- 43 - 18.4.8. Switch on continuous transmission in basic unit Syntax: C1 CR LF Possible answers: C1_I CR LF - command comprehended but cannot be
18.4.11. Switch off continuous transmission in current unit Syntax: CU0 CR LF Possible answers: CU0_I CR LF - command comprehended but cannot be
- 45 - Stability character [space] if stable [?] if not stable [^] if an indication over the range [v] if fan indication below the range sign [space
- 46 - 19. ERROR COMMANDS Err2 - Value beyond the zero range Err3 - Value beyond the tare range Err4 - Calibration mass or start mass beyond the
- 47 - 21. TROUBLE SHOOTING Problem Cause Solution Discharged batteries. Connect to mains or change batteries Turning on does not work No batteries
MANUFACTURER OF ELECTRONIC WEIGHING INSTRUMENTS RADWAG WAGI ELEKTRONICZNE 26 – 600 Radom, Bracka 28 Street POLAND Tel. +48 48 38 48 800,
- 5 - 1. INTENDED USE Platform scales are designed for fast and precise measurements of weighed loads masses and direct commercial settlements. Tarr
The device connected to mains inteligently monitors the battery state and charges it if possible. After sudden lack of power supply from the mains t
2.2.2. Replacement of worn batteries Users have the ability to replace worn out batteries to new ones in weighing indicators PUE C/31 (plastic cas
In PUE C/31H and PUE C/31H/Z weighing indicators (stainless steel housing) the worn out accumulator can be exchanged to a new one by the authorized
G. Contact with the central authorized service: +48 48 384 88 00 ext. 106 or 107. 4. MAIN DIMENSIONS Scales of WPT/P 2 series Scales
Commentaires sur ces manuels